No historical statistics will be available, e.g. position:relative; Step 6:You will then be directed to the router's web-based setup page. information, including user profiles and network settings, will not be transferred to LCM2. The Guest network is a separate network that, Closing the account means deactivating an email address that has a Linksys cloud account associated to it. Please make sure you are What processors do the Linksys EA6350 v1, v2 and v3 use? devices purchased with the LCM1 firmware including LAPAC1200C, LAPAC1750C, LAPAC2600C and all regional Which wireless band can I use to achieve a speed of up to 867 Mbps? padding: 10px 10px 35px; Either one of them can be the primary router. When you say repeater, I assume you mean to act as a range extender (Where the EA6350 would connect wirelessly to another router and then extend the range?) QUICK TIP: Wireless Repeater Mode uses one (1) of the wireless network bands to connect to your upstream router. }. .key-feature-block{ How many Internet connection types does the Linksys EA6350 support? Some Linksys Smart Wi-Fi Routers support Wireless Repeater mode. I tried to play around with it but it seem this router is missing a repeater mode. Not included in LCM2 launch version. If you mean to put it in bridge mode, where you connect an ethernet cable between the two routers and have it extend the signal that way, yes. other features. Is there any way to turn the EA6350 into a repeater? You will have to use this new IP Address to log in to the router’s web-based setup page if you need to configure it later on. For other router models, the username is left blank while the password is admin. To back up the router settings, access your Linksys cloud account. .key-feature-block{ Setting your Linksys Smart Wi-Fi Router to Bridge Mode is applicable when you want to: NOTE:  Setting your Linksys Smart Wi-Fi Router to Bridge Mode will disable all its router capabilities and turn it into an access point. For all other 5. Important facts to be aware of before migrating: Once Access Points are upgraded with the new LCM2 firmware, these Access Points cannot revert To do this, press and hold the Reset button for 10 seconds using a pen or a paper clip. It can now be used as an access point which is helpful in extending your wireless network.NOTE:  In case your router stopped working while it is set to Bridge Mode, you can do any of the following: Related Articles: Setting up WEP, WPA or WPA2 wireless securityPersonalizing and connecting to the 5 GHz wireless band on a Linksys Wi-Fi RouterConnecting wireless computers to your network. For North American phone support, call our Do not connect anything to the Internet port for now. For North American phone support, call our Data usage statistics of clients and APs will be real-time only – i.e., populating for the When you run the Smart Setup, the wizard will automatically generate system-generated settings for you. For any technical issues, please consult our online Linksys Cloud exception of configuring connection parameters, i.e. Manager 1.0 (LCM1) accessible via www.business.linksys.com to Linksys Cloud Manager 2.0 (LCM2) accessible via www.cloudmanager.linksys.com for all Does the Linksys EA6350 support Remote Management? bottom: 10px; back to LCM1 firmware or be used with the LCM1 platform. Both frequency bands, however, can be used for broadcasting to connect other clients. Check out our Privacy Policy if you'd like to learn more. If you have a Linksys Smart Wi-Fi, you can set your router to Bridge Mode by following the instructions here.QUICK TIP:  The Linksys Connect software features will be disabled on the router once Bridge Mode is set up. To check if your router has this option, log in to the router's web-based setup page and click on Connectivity > Internet Settings. Should you prefer Mesh Wifi System or if you are planning to, we recommend you setting up the Velop Node as the primary router as suggested by @Mark_Capul. left: 0; Please tell us how we can make this article useful. , but is also backward-compatible with older versions of USB. to see your support options or contact your local Linksys office for more information. Linksys will continue to operate the LCM1 platform for the duration of the 5 year term offered, What is MAC Address Clone and what is it used for? Those that are comfortable with the functionality provided in LCM1 do not have to migrate Press [Enter]. Both frequency bands in Repeater mode will still broadcast and clients will be able to connect to either of those frequency bands.