Control Panels. 11. Directly controls Wi-Fi garage door openers and myQ-enabled accessories. permit anyone to cross path of closing garage door. When in battery back-up mode, any feature using unattended operation such as Timer-to-Close, closure from a garage door and gate monitor or remote operation utilizing the LiftMaster, 1. State. When the control panel is operational, the yellow command LED will glow steadily. © 2012–2020, manualsdir.comAll rights reserved. City. To test the control panel, press the push bar to activate the garage. will blink quickly for up to 5 minutes as the control panel recharges. Last Name. Control Panels. Automatic lighting. Control Panel is intended to be installed with Security✚™, Garage Door Openers manufactured between 1998 and present. Note the polarity of the wires connected to the existing door. Phone Number. NEVER. 3. Email Address. 6. Openers. 900MHz signal to provide two-way communication between the garage door opener and MyQ enabled accessories. Send us an email and we will respond back to you within two (2) business … Control Panels. Equipped with a 150° sensing angle motion detector. While holding the Lock button, press and hold the Light button on the door control. 7. The yellow command LED and the red learn LED. Press and hold the Lock button on the MyQ Control Panel. The MyQ, Control Panel is NOT compatible with Security✚ 2.0™ Garage Door. LiftMaster Model 888LM MyQ Control Panel Instructions. Motion-detecting control panel turns on the opener's lights. 6. View and Download LiftMaster 888LM MyQ Control Panel instruction manual online. Easy Programing. The MyQ Control Panel offers a quick and convenient way to add Security+ 2.0 and MyQ technology to your existing garage door opener. 10. The yellow command LED and the red learn LED . DO NOT install this door control on garage door opener systems controlling one-piece or swing doors. Program Easily. To prevent possible SERIOUS INJURY or DEATH from a closing garage door:• Install door control within sight of garage door, out of reach of. Reconnect power. • ALWAYS keep garage door in sight until completely closed. On the 828LM Internet Gateway, the LED turns blue once the device is learned in. Street Address. You’ll receive the coupon code via email. • NEVER permit children to operate or play with door control push, • Activate door ONLY when it can be seen clearly, is properly. LiftMaster-Model-888LM-MyQ-Control-Panel-Instructions-1484145667832 . After the opener lights flash, release all three buttons. The manual does not show the instructions for programming the light to one of the remote buttons. Press the MyQ ® Control Panel LEARN button twice, the red learn LED will turn on. Download Instructions . Disconnect the wires from the existing door control. With the door closed, press and hold a small remote button that you want to control the light. Equipped with a 150° sensing angle motion detector. 7. Disconnect all electrical and battery power (if applicable) to the, 2. On the LiftMaster equipment page, clickAdd Device underDevice Commands for the Internet Gateway to add a garage door opener to. Monday-Friday: 8:00am-8:00pm EDT. adjusted, and there are no obstructions to door travel. 2. You may program up to 12 Security✚ 2.0™ remote controls, 2 Security✚ 2.0™ keyless entries and a combination of 16 MyQ, Model 890MAX 3-Button Mini MAX Remote Control, Model 895MAX 3-Button Premium MAX Remote Control, Control Panel in place of the existing door control. Mount the MyQ ® Control Panel to the wall. children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door. This puts the Internet Gateway into learn mode so that MyQ Control Panel (888LM) can be If an additional door control is needed, the wireless door control model 885LM can be programmed to the MyQ, control programming steps. With the door closed, press and hold a small remote button that you want to control the light. Sync remote controls and myQ-Enabled accessories directly from the control panel. Call LiftMaster Partner Support. Press the MyQ Control Panel LEARN KEYLESS ENTRY button twice, the red learn LED will turn 1. Press and hold the Lock button on the MyQ Control Panel.